Basic Info.

Model NO.

Amazing RTO

Type

Incinerator

Low Maintenance

100

Easy Operation

100

Energy Saving

100

High Efficiency

100

Trademark

Bjamazing

Transport Package

Overseas

Specification

111

Origin

China

HS Code

2221111

Product Description

RTO

Regenerative Thermal Oxidizer

Compared with traditional catalytic combustion, direct thermal oxidizer, RTO has the merits of high heating efficiency, low operation cost, and the ability to treat large flux low concentration waste gas. When VOCs concentration is high, secondary heat recycle can be realized, which will greatly reduce the operation cost. Because RTO can preheat the waste gas by levels through ceramic heat accumulator, which could make the waste gas to be completely heated and cracked with no dead corner(treatment efficiency>99%),which reduce the NOX in the Exhausting gas, if the VOC density >1500mg/Nm3, when the waste gas reach cracking area, it has been heated up to cracking temperature by heat accumulator, the burner will be closed under this condition.

RTO can be devided into chamber type and rotary type according to difference operation mode. Rotary type RTO has advantages in system pressure, temperature stability, investment amount, etc

RTO types   Efficiency Pressure change
(mmAq)
Size (max)Treatment volume  
 
Treatment efficiency  Heat recycle efficiency  
Rotary type RTO 99 % 97 % 0-4 small
(1 time)
50000Nm3/h  
Three chamber type RTO 99 % 97 %   0-10 Large
(1.5times)
100000Nm3/h
Two chamber type RTO 95 % 95 % 0-20 middle
(1.2times)
100000Nm3/h  

Regenerative Thermal Oxidizer, Regenerative Thermal Oxidizer, Regenerative Thermal Oxidizer,  Thermal Oxidizer, Thermal Oxidizer, Thermal Oxidizer, oxidizer, oxidizer, oxidizer, incinerator, incinerator, incinerator, waste gas treatment, waste gas treatment, waste gas treatment, VOC treatment, VOC treatment, VOC treatment, RTO, RTO, RTO, Rotary RTO, Rotary RTO, Rotary RTO, Chamber RTO, Chamber RTO, Chamber RTO

Address: 8 floor, E1, Pinwei building, Dishengxi road, Yizhuang, ZheJiang , China

Business Type: Manufacturer/Factory, Trading Company

Business Range: Electrical & Electronics, Industrial Equipment & Components, Manufacturing & Processing Machinery, Metallurgy, Mineral & Energy

Management System Certification: ISO 9001, ISO 14001

Main Products: Rto, Color Coating Line, Galvanizing Line, Air Knife, Spares for Processing Line, Coater, Independent Equipments, Sink Roll, Revamping Project, Blower

Company Introduction: ZheJiang Amazing Science & Technology Co., Ltd is a thriving Hi-tech company, located in ZheJiang Economic and Technological Development Area(BDA). Adhering to the concept of Realistic, Innovative, Focused and Efficient, our company mainly serve the waste gas treatment (VOCs) Industry and metallurgical equipment of China and even whole world. We have advanced technology and rich experience in VOCs waste gas treatment project, the reference of which has been successfully applied to the industry of coating, rubber, electronic, printing, etc. We also have years of technology accumulation in the research and manufacturing of flat steel processing line, and possess nearly 100 of application example.

Our company focus on the research, design, manufacturing, installation and commissioning of VOCs organic waste gas treatment system and the revamping and updating project for energy saving and environmental protection of flat steel processing line. We can provide customers the complete solutions for environmental protection, energy saving, product quality improvement and other aspects.

We are also engaged in various spares and independent equipment for color coating line, galvanizing line, pickling line, like roller, coupler, heat exchanger, recuperator, air knife, blower, welder, tension leveler, skin pass, expansion joint, shear, jointer, stitcher, burner, radiant tube, gear motor, reducer, etc.

regenerative thermal oxidizers

Can regenerative thermal oxidizers be used for abating hazardous air pollutants (HAPs)?

Yes, regenerative thermal oxidizers (RTOs) can be used effectively for abating hazardous air pollutants (HAPs). RTOs are widely recognized and employed as one of the most efficient and reliable technologies for the destruction of a wide range of volatile organic compounds (VOCs) and hazardous air pollutants.

Here are some key points regarding the use of RTOs for abating HAPs:

  • High Destruction Efficiency: RTOs are known for their high destruction efficiency, which refers to their ability to effectively oxidize and destroy HAPs. The combustion chamber within the RTO is designed to maintain a sufficiently high temperature (typically above 1,400°F or 760°C) to ensure complete oxidation of the pollutants, including HAPs.
  • Wide Applicability: RTOs can handle a wide range of HAPs and VOCs, including but not limited to benzene, toluene, xylene, chlorinated compounds, formaldehyde, and various other organic pollutants. Their versatility makes them suitable for diverse industrial applications where HAPs may be present.
  • Retention Time: RTOs are designed with a sufficient residence or retention time within the combustion chamber. This allows the exhaust gases containing HAPs to spend enough time in the high-temperature zone, ensuring that HAPs are adequately treated and oxidized to harmless byproducts.
  • Heat Recovery: The heat recovery system in an RTO, typically using ceramic media beds or heat exchangers, plays a crucial role in the destruction of HAPs. The heat recovery system helps maintain the required temperature and provides thermal energy to sustain the combustion process, ensuring effective destruction of HAPs even during variable operating conditions.
  • Compliance with Regulations: RTOs are designed to meet stringent environmental regulations governing HAP emissions. By effectively destroying HAPs, RTOs help industries comply with air quality standards and emission limits set by regulatory agencies.
  • Monitoring and Controls: RTOs are equipped with advanced monitoring and control systems that continuously monitor parameters such as temperature, pressure, and pollutant concentrations. These systems ensure the optimal performance of the RTO in treating HAPs and allow for adjustments and optimization as needed.

It’s important to note that the specific design and configuration of an RTO may need to be tailored to the characteristics of the HAPs being treated. Factors such as the HAPs’ chemical composition, concentration, and other process-specific considerations may influence the selection and customization of the RTO system.

In summary, RTOs are highly effective and reliable technologies for abating hazardous air pollutants. Their high destruction efficiency, wide applicability, and compliance with regulations make them a preferred choice for industries seeking to mitigate the environmental impact of HAP emissions.

regenerative thermal oxidizers

What are the startup and shutdown time requirements for a regenerative thermal oxidizer?

The startup and shutdown time requirements for a regenerative thermal oxidizer (RTO) can vary depending on several factors, including the specific design of the RTO, the size of the system, and the operating conditions. Here are some key points regarding the startup and shutdown time requirements for an RTO:

  • Startup Time: The startup time for an RTO typically refers to the time it takes for the system to reach its operating temperature and stabilize for effective emission control. The startup time can range from several hours to several days, depending on the size of the RTO, the thermal capacity of the heat exchange media, and the desired operating temperature. During startup, the RTO gradually heats up the heat exchange beds or media using a burner system or other heating mechanisms until the desired temperature is reached.
  • Shutdown Time: The shutdown time for an RTO refers to the time it takes to safely cool down the system and bring it to a complete stop. The shutdown time can also vary and may range from several hours to several days. During shutdown, the flow of exhaust gas is stopped, and the RTO initiates a cooling process to lower the temperature of the heat exchange media. Cooling mechanisms such as air or water may be used to expedite the cooling process and ensure safe operation.
  • System Requirements: The specific startup and shutdown time requirements for an RTO are often determined by the process requirements, operational needs, and regulatory compliance. Some applications may require faster startup and shutdown times to accommodate frequent process changes, while others may prioritize energy efficiency and opt for longer startup and shutdown times to allow for heat recovery and minimize fuel consumption.
  • Control Systems: Advanced control systems are typically employed to monitor and control the startup and shutdown processes of an RTO. These systems ensure that the temperature ramp-up and ramp-down rates are within safe limits and that the system operates efficiently and reliably during these phases.

It is essential to consult with RTO manufacturers or experienced engineers to determine the specific startup and shutdown time requirements for a particular RTO based on its design, size, and intended application. They can provide guidance on optimizing the startup and shutdown processes to meet the operational and regulatory needs while ensuring the safe and efficient operation of the RTO.

In summary, the startup and shutdown time requirements for an RTO can vary depending on factors such as system design, size, and operational considerations. Startup times can range from hours to days, while shutdown times can also vary. These requirements are tailored to meet the specific needs of the process and ensure effective emission control while maintaining operational safety.

regenerative thermal oxidizers

What are the maintenance requirements for a regenerative thermal oxidizer?

Maintaining a regenerative thermal oxidizer (RTO) is essential to ensure its optimal performance, longevity, and compliance with environmental regulations. Here are some key maintenance requirements for an RTO:

  • Regular Inspections: Conduct routine inspections to identify any signs of wear, corrosion, or damage to the RTO components. This includes inspecting valves, dampers, fans, combustion chambers, heat exchangers, and ceramic media beds. Inspections help detect potential issues early and allow for timely repairs or replacements.
  • Cleaning and Replacement of Components: Clean or replace components as needed to maintain proper functionality. This may include cleaning clogged or fouled heat exchanger surfaces, replacing damaged or worn-out valves and dampers, and periodically replacing the ceramic media beds if they become degraded or contaminated.
  • Monitoring Operating Parameters: Regularly monitor and record operating parameters such as temperature, airflow, pressure differentials, and gas concentrations. Deviations from normal operating ranges can indicate potential problems or inefficiencies that require attention.
  • Calibration of Instruments: Calibrate instruments and sensors used for monitoring and control purposes to ensure accurate measurement of parameters such as temperature, pressure, and flow rates. Proper calibration helps maintain reliable and precise operation of the RTO.
  • Cleaning of Heat Recovery System: Clean the heat recovery system, including the heat exchanger surfaces, to remove any accumulated particulate matter or fouling. This ensures efficient heat transfer and prevents the buildup of deposits that can reduce the RTO’s performance.
  • Compliance with Safety Standards: Adhere to safety standards and guidelines for working with the RTO. This includes proper lockout/tagout procedures during maintenance activities, wearing appropriate personal protective equipment, and following safety protocols to minimize risks to personnel and equipment.
  • Documentation and Record-Keeping: Maintain comprehensive records of maintenance activities, inspections, repairs, and any modifications made to the RTO. Documentation helps track the equipment’s history, aids in troubleshooting, and provides a record of compliance with regulatory requirements.

It’s important to note that the specific maintenance requirements may vary depending on the RTO manufacturer’s recommendations, the design of the system, the operating conditions, and applicable regulatory requirements. Following the manufacturer’s guidelines, conducting regular inspections, and implementing a proactive maintenance program tailored to the specific RTO are crucial for ensuring its reliable operation and longevity.

China manufacturer Rto Rotary Type Regenerative Thermal Oxidizer
editor by CX 2023-10-19

en_USEN