Basic Info.
Model NO.
Amazing RTO
Type
Incinerator
Energy Saving
100
Easy for Operation
100
High Efficiency
100
Less Maintenance
100
Trademark
Bjamazing
Transport Package
Overseas Wooden
Specification
180*24
Origin
China
HS Code
8416100000
Product Description
RTO
Regenerative Thermal Oxidizer
Compared with traditional catalytic combustion,; direct thermal oxidizer,; RTO has the merits of high heating efficiency,; low operation cost,; and the ability to treat large flux low concentration waste gas.; When VOCs concentration is high,; secondary heat recycle can be realized,; which will greatly reduce the operation cost.; Because RTO can preheat the waste gas by levels through ceramic heat accumulator,; which could make the waste gas to be completely heated and cracked with no dead corner(treatment efficiency>99%);,;which reduce the NOX in the Exhausting gas,; if the VOC density >1500mg/Nm3,; when the waste gas reach cracking area,; it has been heated up to cracking temperature by heat accumulator,; the burner will be closed under this condition.;
RTO can be devided into chamber type and rotary type according to difference operation mode.; Rotary type RTO has advantages in system pressure,; temperature stability,; investment amount,; etc
Recuperative thermal oxidizer:;
Compared with the catalytic combustion and regenerative thermal oxidation furnace,; recuperative thermal oxidizer investment is less .; Recuperative thermal oxidizer system can be designed for the entire incineration system as well as the new air system,; which is more suitable for production characteristics of coating units for building materials plate.;
| Burning type | Treatment system | efficiency | Advantage | Disadvantage | |
| Treating efficiency | Heat recycle rate | ||||
| High temperature incineration | Regenerative-RTO | 99 % | 80-97 % | Good product quality,; low energy consumption,; low cost in operational and minimum maintenance | Initial investment is somewhat of higher |
| Recuperative-RTO | 98 % | 40-70 % | When adopt full incinerating design,; the energy consumption is low | High temperature joint interface is easy to broken,; maintenance cost is high | |
| Low temperature incineration | Catalyzing-RCO | 98 % | 70-85 % | Low investment,; low energy consumption | VOC concentration has to be controlled strictly,; catalyst need to be changed regularly |
| Active carbon absorption | 90 % | Lower investment,; self aggregation waste gas can be treated | Treatment efficiency is low,; activated carbon particle need to be replaced regularly | ||
Regenerative Thermal Oxidizer,; Regenerative Thermal Oxidizer,; Recuperative Thermal Oxidizer,; recuperative Thermal Oxidizer,; recuperative Thermal Oxidizer,; Thermal Oxidizer,; oxidizer,; oxidizer,; oxidizer,; incinerator,; incinerator,; incinerator,; waste gas treatment,; waste gas treatment,; waste gas treatment,; VOC treatment,; VOC treatment,; VOC treatment,; RTO,; RTO,; RTO,; RTO,; RTO,; RTO
Address: 8 floor, E1, Pinwei building, Dishengxi road, Yizhuang, ZheJiang , China
Business Type: Manufacturer/Factory, Trading Company
Business Range: Electrical & Electronics, Industrial Equipment & Components, Manufacturing & Processing Machinery, Metallurgy, Mineral & Energy
Management System Certification: ISO 9001, ISO 14001
Main Products: Rto, Color Coating Line, Galvanizing Line, Air Knife, Spares for Processing Line, Coater, Independent Equipments, Sink Roll, Revamping Project, Blower
Company Introduction: ZheJiang Amazing Science & Technology Co., Ltd is a thriving Hi-tech company, located in ZheJiang Economic and Technological Development Area(BDA). Adhering to the concept of Realistic, Innovative, Focused and Efficient, our company mainly serve the waste gas treatment (VOCs) Industry and metallurgical equipment of China and even whole world. We have advanced technology and rich experience in VOCs waste gas treatment project, the reference of which has been successfully applied to the industry of coating, rubber, electronic, printing, etc. We also have years of technology accumulation in the research and manufacturing of flat steel processing line, and possess nearly 100 of application example.
Our company focus on the research, design, manufacturing, installation and commissioning of VOCs organic waste gas treatment system and the revamping and updating project for energy saving and environmental protection of flat steel processing line. We can provide customers the complete solutions for environmental protection, energy saving, product quality improvement and other aspects.
We are also engaged in various spares and independent equipment for color coating line, galvanizing line, pickling line, like roller, coupler, heat exchanger, recuperator, air knife, blower, welder, tension leveler, skin pass, expansion joint, shear, jointer, stitcher, burner, radiant tube, gear motor, reducer, etc.
How do regenerative thermal oxidizers compare to catalytic oxidizers?
Regenerative thermal oxidizers (RTOs) and catalytic oxidizers are both effective technologies used for controlling air emissions from industrial processes. While they serve a similar purpose, there are significant differences in their operation, efficiency, and applicability.
Here is a comparison between RTOs and catalytic oxidizers:
| Regenerative Thermal Oxidizers (RTOs) | Catalytic Oxidizers |
|---|---|
| Operation: | Operation: |
| RTOs achieve emission control through high-temperature combustion without the use of a catalyst. They rely on the thermal oxidation process, where VOCs and other pollutants in the exhaust gas are oxidized at high temperatures (typically between 1,400°F and 1,600°F) in the presence of excess oxygen. | Catalytic oxidizers utilize a catalyst (usually a precious metal, such as platinum, palladium, or rhodium) to facilitate the oxidation of VOCs and other pollutants at lower temperatures compared to RTOs. The catalyst lowers the activation energy required for the oxidation reaction, enabling it to occur at lower temperatures (around 600°F to 900°F). |
| Efficiency: | Efficiency: |
| RTOs are known for their high thermal efficiency. They utilize a regenerative heat exchanger system that recovers and transfers heat from the treated exhaust gases to the incoming untreated gases, significantly reducing fuel consumption. This heat recovery mechanism makes RTOs energy-efficient. | Catalytic oxidizers are generally more energy-efficient than RTOs because they operate at lower temperatures. The catalyst facilitates the oxidation reaction, allowing it to occur at lower temperatures, which reduces the energy requirement for heating the exhaust gas. |
| Applicability: | Applicability: |
| RTOs are particularly suitable for applications where the pollutant concentrations are high, or where there is a wide variation in flow rates or pollutant concentrations. They are commonly used for the control of volatile organic compounds (VOCs) and hazardous air pollutants (HAPs) in various industries, including chemical manufacturing, printing, coating, and pharmaceuticals. | Catalytic oxidizers are often preferred in applications where the pollutant concentrations are relatively low and relatively constant. They are effective for VOC control in applications such as automotive painting, printing, and food processing, where the VOC concentrations can be lower and more consistent. |
| Limitations: | Limitations: |
| RTOs have higher capital costs compared to catalytic oxidizers due to their complex design and heat recovery system. They also have a higher operating temperature, which may limit their applicability in certain processes or require additional heat recovery systems. | Catalytic oxidizers can be sensitive to poisons or contaminants in the exhaust gas that can deactivate or degrade the catalyst over time. Certain compounds, such as sulfur, silicones, or halogenated compounds, can potentially poison the catalyst, reducing its effectiveness and requiring periodic catalyst replacement or regeneration. |
When selecting between an RTO and a catalytic oxidizer, it is essential to consider the specific requirements of the application, including pollutant concentrations, flow rates, temperature requirements, and cost considerations. Consulting with environmental engineering professionals or equipment manufacturers can help determine the most suitable technology for a particular emission control need.
Are regenerative thermal oxidizers suitable for controlling emissions from printing presses?
Yes, regenerative thermal oxidizers (RTOs) can be suitable for controlling emissions from printing presses. Printing presses can emit volatile organic compounds (VOCs) and other air pollutants during the printing process, which need to be properly controlled to comply with environmental regulations and ensure air quality. Here are some key points regarding the suitability of RTOs for controlling emissions from printing presses:
- Emission Control: RTOs are designed to achieve high destruction efficiencies for VOCs and hazardous air pollutants (HAPs). These pollutants are oxidized within the RTO at high temperatures, typically above 95% efficiency, converting them into carbon dioxide (CO2) and water vapor. RTOs effectively control and reduce emissions from printing presses.
- Compatibility: RTOs can be integrated into the exhaust system of printing presses, capturing and treating the emissions before they are released into the atmosphere. The RTO is typically connected to the exhaust stack of the printing press, allowing the VOC-laden air to pass through the oxidizer for treatment.
- High Flow Rates: Printing presses can generate significant exhaust volumes due to the printing process. RTOs are designed to handle high flow rates and can accommodate the varying exhaust volumes of printing presses. This ensures effective treatment of emissions even during peak production periods.
- Thermal Capacity: RTOs have the thermal capacity to handle the temperature variations in printing press emissions. The printing process can result in varying exhaust temperatures, and RTOs are designed to operate effectively within a wide range of temperature conditions.
- Energy Efficiency: RTOs incorporate heat exchange systems that allow for the recovery and reuse of thermal energy. The heat exchangers within the RTO capture the heat from the outgoing exhaust gases and transfer it to the incoming process air or gas stream. This heat recovery process improves the overall energy efficiency of the system and reduces the need for additional fuel consumption.
- Compliance with Regulations: Printing press emissions are subject to regulatory requirements for air quality and emissions control. RTOs are capable of achieving the necessary destruction efficiencies and can help printing press operators comply with environmental regulations. The use of RTOs demonstrates a commitment to sustainable practices and responsible management of air emissions.
It is important to note that the specific design and configuration of the RTO, as well as the characteristics of the printing press emissions, should be considered when implementing an RTO for a printing press application. Consulting with experienced engineers or RTO manufacturers can provide valuable insights into the proper sizing, integration, and performance requirements for controlling emissions from printing presses.
In summary, RTOs are a suitable technology for controlling emissions from printing presses, providing high destruction efficiencies, compatibility with printing press exhaust systems, handling high flow rates and temperature variations, energy efficiency through heat recovery, and compliance with environmental regulations.
How does a regenerative thermal oxidizer work?
A regenerative thermal oxidizer (RTO) is an advanced air pollution control device that operates through a cyclical process to remove volatile organic compounds (VOCs), hazardous air pollutants (HAPs), and other airborne contaminants from exhaust gases. Here’s a detailed explanation of how an RTO works:
1. Inlet Plenum: The exhaust gases containing pollutants enter the RTO through the inlet plenum.
2. Heat Exchanger Beds: The RTO contains multiple heat exchanger beds filled with heat storage media, typically ceramic materials or structured packing. The heat exchanger beds are arranged in pairs.
3. Flow Control Valves: Flow control valves direct the airflow and control the direction of the exhaust gases through the RTO.
4. Combustion Chamber: The exhaust gases, now directed into the combustion chamber, are heated to a high temperature, typically between 1400°F (760°C) and 1600°F (870°C). This temperature range ensures effective thermal oxidation of the pollutants.
5. VOC Destruction: The high temperature in the combustion chamber causes the VOCs and other contaminants to react with oxygen, resulting in their thermal decomposition or oxidation. This process breaks down the pollutants into water vapor, carbon dioxide, and other harmless gases.
6. Heat Recovery: The hot, purified gases leaving the combustion chamber pass through the outlet plenum and flow through the heat exchanger beds that are in the opposite phase of operation. The heat storage media in the beds absorb heat from the outgoing gases, which preheats the incoming exhaust gases.
7. Cycle Switching: After a specific time interval, the flow control valves switch the airflow direction, allowing the heat exchanger beds that were preheating the incoming gases to now receive the hot gases from the combustion chamber. The cycle then repeats, ensuring continuous and efficient operation.
Advantages of a regenerative thermal oxidizer:
RTOs offer several advantages in industrial air pollution control:
1. High Efficiency: RTOs can achieve high destruction efficiencies, typically above 95%, effectively removing a wide range of pollutants.
2. Energy Recovery: The heat recovery mechanism in RTOs allows for significant energy savings. The preheating of incoming gases reduces the fuel consumption required for combustion, making RTOs energy-efficient.
3. Cost-effectiveness: Although the initial capital investment for an RTO can be significant, the long-term operational cost savings through energy recovery and high destruction efficiencies make it a cost-effective solution over the lifespan of the system.
4. Environmental Compliance: RTOs are designed to meet stringent emissions regulations and help industries comply with air quality standards and permits.
5. Versatility: RTOs can handle a wide range of process exhaust volumes and pollutant concentrations, making them suitable for various industrial applications.
Overall, a regenerative thermal oxidizer operates by utilizing heat recovery, high-temperature combustion, and cyclical flow control to effectively oxidize pollutants and achieve high destruction efficiencies while minimizing energy consumption.
editor by Dream 2024-10-08
EN 
ZH 
ES 
AR 
ID 
PT 
FR 
JA 
RU 
DE 
MS 
CS 
BG 
NL 
KO 
RO 
SK 
TH 
VI 
ZH_TW 
UK