China manufacturer Rto Rotary Type Regenerative Thermal Oxidizer

Maklumat Asas.

Model NO.

RTO yang menakjubkan

taip

Insinerator

Penyelenggaraan Rendah

100

Operasi Mudah

100

Penjimatan Tenaga

100

Kecekapan Tinggi

100

Tanda dagangan

Bjamazing

Pakej Pengangkutan

Luar negara

Spesifikasi

111

asal usul

China

Kod HS

2221111

Penerangan Produk

RTO

Pengoksida Terma Penjanaan Semula

Compared with traditional catalytic combustion, direct thermal oxidizer, RTO has the merits of high heating efficiency, low operation cost, and the ability to treat large flux low concentration waste gas. When VOCs concentration is high, secondary heat recycle can be realized, which will greatly reduce the operation cost. Because RTO can preheat the waste gas by levels through ceramic heat accumulator, which could make the waste gas to be completely heated and cracked with no dead corner(treatment efficiency>99%),which reduce the NOX in the Exhausting gas, if the VOC density >1500mg/Nm3, when the waste gas reach cracking area, it has been heated up to cracking temperature by heat accumulator, the burner will be closed under this condition.

RTO can be devided into chamber type and rotary type according to difference operation mode. Rotary type RTO has advantages in system pressure, temperature stability, investment amount, etc

Regenerative Thermal Oxidizer, Regenerative Thermal Oxidizer, Regenerative Thermal Oxidizer,  Thermal Oxidizer, Thermal Oxidizer, Thermal Oxidizer, oxidizer, oxidizer, oxidizer, incinerator, incinerator, incinerator, waste gas treatment, waste gas treatment, waste gas treatment, VOC treatment, VOC treatment, VOC treatment, RTO, RTO, RTO, Rotary RTO, Rotary RTO, Rotary RTO, Chamber RTO, Chamber RTO, Chamber RTO

Alamat: tingkat 8, E1, bangunan Pinwei, jalan Dishengxi, Yizhuang, ZheJiang, China

Jenis Perniagaan: Pengeluar/Kilang, Syarikat Perdagangan

Julat Perniagaan: Elektrik & Elektronik, Peralatan & Komponen Industri, Jentera Pembuatan & Pemprosesan, Metalurgi, Mineral & Tenaga

Pensijilan Sistem Pengurusan: ISO 9001, ISO 14001

Produk Utama: Rto, Talian Salutan Warna, Talian Galvanisasi, Pisau Udara, Alat Ganti untuk Talian Pemprosesan, Coater, Peralatan Bebas, Gulung Sink, Projek Ubahsuai, Blower

Pengenalan Syarikat: ZheJiang Amazing Science & Technology Co., Ltd ialah sebuah syarikat berteknologi tinggi yang berkembang maju, terletak di ZheJiang Economic and Technological Development Area(BDA). Berpegang kepada konsep Realistik, Inovatif, Fokus dan Cekap, syarikat kami menyediakan perkhidmatan terutamanya dalam industri rawatan gas sisa (VOC) dan peralatan metalurgi China dan juga seluruh dunia. Kami mempunyai teknologi canggih dan pengalaman yang kaya dalam projek rawatan gas buangan VOC, yang rujukannya telah berjaya digunakan untuk industri salutan, getah, elektronik, percetakan, dll. Kami juga mempunyai pengumpulan teknologi selama bertahun-tahun dalam penyelidikan dan pembuatan flat talian pemprosesan keluli, dan mempunyai hampir 100 contoh aplikasi.

Syarikat kami menumpukan pada penyelidikan, reka bentuk, pengilangan, pemasangan dan pentauliahan sistem rawatan gas sisa organik VOC dan projek merombak dan mengemas kini untuk penjimatan tenaga dan perlindungan alam sekitar barisan pemprosesan keluli rata. Kami boleh menyediakan pelanggan penyelesaian lengkap untuk perlindungan alam sekitar, penjimatan tenaga, peningkatan kualiti produk dan aspek lain.

Kami juga terlibat dalam pelbagai alat ganti dan peralatan bebas untuk garis salutan warna, garis galvanizing, garis penjerukan, seperti penggelek, pengganding, penukar haba, recuperator, pisau udara, peniup, pengimpal, penyamara ketegangan, pas kulit, sambungan pengembangan, ricih, penyambung , penjahit, penunu, tiub berseri, motor gear, pengurang, dsb.

Can regenerative thermal oxidizers be used for abating hazardous air pollutants (HAPs)?

Yes, regenerative thermal oxidizers (RTOs) can be used effectively for abating hazardous air pollutants (HAPs). RTOs are widely recognized and employed as one of the most efficient and reliable technologies for the destruction of a wide range of volatile organic compounds (VOCs) and hazardous air pollutants.

Here are some key points regarding the use of RTOs for abating HAPs:

• High Destruction Efficiency: RTOs are known for their high destruction efficiency, which refers to their ability to effectively oxidize and destroy HAPs. The combustion chamber within the RTO is designed to maintain a sufficiently high temperature (typically above 1,400°F or 760°C) to ensure complete oxidation of the pollutants, including HAPs.
• Wide Applicability: RTOs can handle a wide range of HAPs and VOCs, including but not limited to benzene, toluene, xylene, chlorinated compounds, formaldehyde, and various other organic pollutants. Their versatility makes them suitable for diverse industrial applications where HAPs may be present.
• Retention Time: RTOs are designed with a sufficient residence or retention time within the combustion chamber. This allows the exhaust gases containing HAPs to spend enough time in the high-temperature zone, ensuring that HAPs are adequately treated and oxidized to harmless byproducts.
• Pemulihan Haba: The heat recovery system in an RTO, typically using ceramic media beds or heat exchangers, plays a crucial role in the destruction of HAPs. The heat recovery system helps maintain the required temperature and provides thermal energy to sustain the combustion process, ensuring effective destruction of HAPs even during variable operating conditions.
• Pematuhan dengan Peraturan: RTOs are designed to meet stringent environmental regulations governing HAP emissions. By effectively destroying HAPs, RTOs help industries comply with air quality standards and emission limits set by regulatory agencies.
• Monitoring and Controls: RTOs are equipped with advanced monitoring and control systems that continuously monitor parameters such as temperature, pressure, and pollutant concentrations. These systems ensure the optimal performance of the RTO in treating HAPs and allow for adjustments and optimization as needed.

It’s important to note that the specific design and configuration of an RTO may need to be tailored to the characteristics of the HAPs being treated. Factors such as the HAPs’ chemical composition, concentration, and other process-specific considerations may influence the selection and customization of the RTO system.

In summary, RTOs are highly effective and reliable technologies for abating hazardous air pollutants. Their high destruction efficiency, wide applicability, and compliance with regulations make them a preferred choice for industries seeking to mitigate the environmental impact of HAP emissions.

What are the startup and shutdown time requirements for a regenerative thermal oxidizer?

The startup and shutdown time requirements for a regenerative thermal oxidizer (RTO) can vary depending on several factors, including the specific design of the RTO, the size of the system, and the operating conditions. Here are some key points regarding the startup and shutdown time requirements for an RTO:

• Startup Time: The startup time for an RTO typically refers to the time it takes for the system to reach its operating temperature and stabilize for effective emission control. The startup time can range from several hours to several days, depending on the size of the RTO, the thermal capacity of the heat exchange media, and the desired operating temperature. During startup, the RTO gradually heats up the heat exchange beds or media using a burner system or other heating mechanisms until the desired temperature is reached.
• Shutdown Time: The shutdown time for an RTO refers to the time it takes to safely cool down the system and bring it to a complete stop. The shutdown time can also vary and may range from several hours to several days. During shutdown, the flow of exhaust gas is stopped, and the RTO initiates a cooling process to lower the temperature of the heat exchange media. Cooling mechanisms such as air or water may be used to expedite the cooling process and ensure safe operation.
• System Requirements: The specific startup and shutdown time requirements for an RTO are often determined by the process requirements, operational needs, and regulatory compliance. Some applications may require faster startup and shutdown times to accommodate frequent process changes, while others may prioritize energy efficiency and opt for longer startup and shutdown times to allow for heat recovery and minimize fuel consumption.
• Control Systems: Advanced control systems are typically employed to monitor and control the startup and shutdown processes of an RTO. These systems ensure that the temperature ramp-up and ramp-down rates are within safe limits and that the system operates efficiently and reliably during these phases.

It is essential to consult with RTO manufacturers or experienced engineers to determine the specific startup and shutdown time requirements for a particular RTO based on its design, size, and intended application. They can provide guidance on optimizing the startup and shutdown processes to meet the operational and regulatory needs while ensuring the safe and efficient operation of the RTO.

In summary, the startup and shutdown time requirements for an RTO can vary depending on factors such as system design, size, and operational considerations. Startup times can range from hours to days, while shutdown times can also vary. These requirements are tailored to meet the specific needs of the process and ensure effective emission control while maintaining operational safety.

Apakah keperluan penyelenggaraan untuk pengoksida terma regeneratif?

Mengekalkan pengoksida terma penjanaan semula (RTO) adalah penting untuk memastikan prestasi optimum, jangka hayat dan pematuhan kepada peraturan alam sekitar. Berikut ialah beberapa keperluan penyelenggaraan utama untuk RTO:

• Pemeriksaan berkala: Lakukan pemeriksaan rutin untuk mengenal pasti sebarang tanda haus, kakisan atau kerosakan pada komponen RTO. Ini termasuk memeriksa injap, peredam, kipas, kebuk pembakaran, penukar haba dan katil media seramik. Pemeriksaan membantu mengesan masalah yang berpotensi lebih awal dan membolehkan pembaikan atau penggantian tepat pada masanya.
• Pembersihan dan Penggantian Komponen: Bersihkan atau gantikan komponen mengikut keperluan untuk mengekalkan kefungsian yang betul. Ini mungkin termasuk membersihkan permukaan penukar haba yang tersumbat atau kotor, menggantikan injap dan peredam yang rosak atau haus, dan menggantikan katil media seramik secara berkala jika ia rosak atau tercemar.
• Memantau Parameter Operasi: Sentiasa memantau dan merekod parameter operasi seperti suhu, aliran udara, pembezaan tekanan dan kepekatan gas. Penyimpangan daripada julat operasi biasa boleh menunjukkan potensi masalah atau ketidakcekapan yang memerlukan perhatian.
• Penentukuran Instrumen: Kalibrasi instrumen dan penderia yang digunakan untuk tujuan pemantauan dan kawalan untuk memastikan pengukuran parameter yang tepat seperti suhu, tekanan dan kadar aliran. Penentukuran yang betul membantu mengekalkan operasi RTO yang boleh dipercayai dan tepat.
• Pembersihan Sistem Pemulihan Haba: Bersihkan sistem pemulihan haba, termasuk permukaan penukar haba, untuk mengeluarkan sebarang zarah terkumpul atau kekotoran. Ini memastikan pemindahan haba yang cekap dan menghalang pengumpulan mendapan yang boleh mengurangkan prestasi RTO.
• Pematuhan dengan Piawaian Keselamatan: Patuhi piawaian dan garis panduan keselamatan untuk bekerja dengan RTO. Ini termasuk prosedur lockout/tagout yang betul semasa aktiviti penyelenggaraan, memakai peralatan pelindung diri yang sesuai, dan mematuhi protokol keselamatan untuk meminimumkan risiko kepada kakitangan dan peralatan.
• Dokumentasi dan Penyimpanan Rekod: Mengekalkan rekod menyeluruh aktiviti penyelenggaraan, pemeriksaan, pembaikan dan sebarang pengubahsuaian yang dibuat kepada RTO. Dokumentasi membantu menjejaki sejarah peralatan, membantu dalam penyelesaian masalah dan menyediakan rekod pematuhan dengan keperluan kawal selia.

Adalah penting untuk ambil perhatian bahawa keperluan penyelenggaraan khusus mungkin berbeza-beza bergantung pada pengesyoran pengilang RTO, reka bentuk sistem, keadaan operasi dan keperluan kawal selia yang berkenaan. Mengikuti garis panduan pengilang, menjalankan pemeriksaan biasa dan melaksanakan program penyelenggaraan proaktif yang disesuaikan dengan RTO khusus adalah penting untuk memastikan operasi yang boleh dipercayai dan jangka hayatnya.

editor by CX 2023-10-19