China wholesaler Rto Rotary Type Regenerative Thermal Oxidizer

基本訊息

型號

Amazing RTO

類型

Incinerator

High Efficiency

100

Energy Saving

100

Low Maintenance

100

Easy Operation

100

商標

Bjamazing

運輸套餐

Overseas

Specification

111

起源

China

HS Code

2221111

產品描述

RTO

蓄熱式熱氧化器

Compared with traditional catalytic combustion,; direct thermal oxidizer,; RTO has the merits of high heating efficiency,; low operation cost,; and the ability to treat large flux low concentration waste gas.; When VOCs concentration is high,; secondary heat recycle can be realized,; which will greatly reduce the operation cost.; Because RTO can preheat the waste gas by levels through ceramic heat accumulator,; which could make the waste gas to be completely heated and cracked with no dead corner(treatment efficiency>99%);,;which reduce the NOX in the Exhausting gas,; if the VOC density >1500mg/Nm3,; when the waste gas reach cracking area,; it has been heated up to cracking temperature by heat accumulator,; the burner will be closed under this condition.;

RTO can be devided into chamber type and rotary type according to difference operation mode.; Rotary type RTO has advantages in system pressure,; temperature stability,; investment amount,; etc

Regenerative Thermal Oxidizer,; Regenerative Thermal Oxidizer,; Regenerative Thermal Oxidizer,;  Thermal Oxidizer,; Thermal Oxidizer,; Thermal Oxidizer,; oxidizer,; oxidizer,; oxidizer,; incinerator,; incinerator,; incinerator,; waste gas treatment,; waste gas treatment,; waste gas treatment,; VOC treatment,; VOC treatment,; VOC treatment,; RTO,; RTO,; RTO,; Rotary RTO,; Rotary RTO,; Rotary RTO,; Chamber RTO,; Chamber RTO,; Chamber RTO

Address: 8 floor, E1, Pinwei building, Dishengxi road, Yizhuang, ZheJiang , China

業務類型: 製造商/工廠, 貿易公司

Business Range: Electrical & Electronics, Industrial Equipment & Components, Manufacturing & Processing Machinery, Metallurgy, Mineral & Energy

Management System Certification: ISO 9001, ISO 14001

Main Products: Rto, Color Coating Line, Galvanizing Line, Air Knife, Spares for Processing Line, Coater, Independent Equipments, Sink Roll, Revamping Project, Blower

Company Introduction: ZheJiang Amazing Science & Technology Co., Ltd is a thriving Hi-tech company, located in ZheJiang Economic and Technological Development Area(BDA). Adhering to the concept of Realistic, Innovative, Focused and Efficient, our company mainly serve the waste gas treatment (VOCs) Industry and metallurgical equipment of China and even whole world. We have advanced technology and rich experience in VOCs waste gas treatment project, the reference of which has been successfully applied to the industry of coating, rubber, electronic, printing, etc. We also have years of technology accumulation in the research and manufacturing of flat steel processing line, and possess nearly 100 of application example.

Our company focus on the research, design, manufacturing, installation and commissioning of VOCs organic waste gas treatment system and the revamping and updating project for energy saving and environmental protection of flat steel processing line. We can provide customers the complete solutions for environmental protection, energy saving, product quality improvement and other aspects.

We are also engaged in various spares and independent equipment for color coating line, galvanizing line, pickling line, like roller, coupler, heat exchanger, recuperator, air knife, blower, welder, tension leveler, skin pass, expansion joint, shear, jointer, stitcher, burner, radiant tube, gear motor, reducer, etc.

蓄熱式熱氧化器與催化氧化器相比如何？

蓄熱式熱氧化器 (RTO) 和催化氧化器都是用來控制工業製程空氣排放的有效技術。雖然它們的用途相似，但在操作、效率和適用性方面存在顯著差異。

以下是 RTO 和催化氧化劑之間的比較：

在 RTO 和催化氧化器之間進行選擇時，必須考慮應用的特定要求，包括污染物濃度、流速、溫度要求和成本考量。諮詢環境工程專業人士或設備製造商可以協助確定最適合特定排放控制需求的技術。

Can regenerative thermal oxidizers be used for treating emissions from paint booths?

Yes, regenerative thermal oxidizers (RTOs) can be effectively used for treating emissions from paint booths. Paint booths generate volatile organic compounds (VOCs) and hazardous air pollutants (HAPs) during the painting process, which need to be controlled to comply with environmental regulations and ensure air quality. Here are some key points regarding the use of RTOs for treating emissions from paint booths:

• Emission Control: RTOs are designed to achieve high destruction efficiencies for VOCs and HAPs. These pollutants are oxidized within the RTO at high temperatures, typically above 95% efficiency, converting them into carbon dioxide (CO₂) and water vapor. This ensures effective control and reduction of emissions from the paint booth.
• Paint Booth Compatibility: RTOs can be integrated into the exhaust system of paint booths, capturing and treating the emissions before they are released into the atmosphere. The RTO is typically connected to the exhaust stack of the paint booth, allowing the VOC-laden air to pass through the oxidizer for treatment.
• Thermal Capacity: Paint booth emissions can vary in terms of flow rate, temperature, and concentration of VOCs. RTOs are designed to handle a wide range of operating conditions and can accommodate high flow rates and elevated temperatures. The system’s thermal capacity ensures effective treatment of emissions from paint booths, even during peak production periods.
• 熱回收： RTOs incorporate heat exchange systems that allow for the recovery and reuse of thermal energy. The heat exchangers within the RTO capture the heat from the outgoing exhaust gases and transfer it to the incoming process air or gas stream. This heat recovery process improves the overall energy efficiency of the system and reduces the need for additional fuel consumption.
• Compliance with Regulations: Paint booth emissions are subject to regulatory requirements for air quality and emissions control. RTOs are capable of achieving the necessary destruction efficiencies and can help paint booth operators comply with environmental regulations. The use of RTOs demonstrates a commitment to sustainable practices and responsible management of air emissions.

It is important to note that the specific design and configuration of the RTO, as well as the characteristics of the paint booth emissions, should be considered when implementing an RTO for a paint booth application. Consulting with experienced engineers or RTO manufacturers can provide valuable insights into the proper sizing, integration, and performance requirements for treating emissions from paint booths.

In summary, RTOs are a suitable and effective technology for treating emissions from paint booths, providing high destruction efficiencies, compatibility with paint booth exhaust systems, thermal capacity for varying operating conditions, heat recovery, and compliance with environmental regulations.

What are the key components of a regenerative thermal oxidizer?

A regenerative thermal oxidizer (RTO) typically consists of several key components that work together to achieve effective air pollution control. The main components of an RTO include:

• 1. Combustion Chamber: The combustion chamber is where the oxidation of the pollutants takes place. It is designed to withstand high temperatures and house the ceramic media beds that facilitate heat exchange and VOC destruction. The combustion chamber provides a controlled environment for the combustion process to occur efficiently.
• 2. Ceramic Media Beds: Ceramic media beds are the heart of an RTO. They are filled with structured ceramic materials that act as a heat sink. The media beds alternate between the inlet and outlet sides of the RTO, allowing for efficient heat transfer. As the VOC-laden air passes through the media beds, it is heated by the stored heat from the previous cycle, promoting combustion and VOC destruction.
• 3. Valves or Dampers: Valves or dampers are used to direct the airflow within the RTO. They control the flow of the process air and the direction of the exhaust gases during the different phases of operation, such as the heating, combustion, and cooling cycles. Proper valve sequencing ensures optimal heat recovery and VOC destruction efficiency.
• 4. Burner System: The burner system provides the necessary heat to raise the temperature of the incoming process air to the required combustion temperature. It typically uses natural gas or another fuel source to generate the heat energy needed for the destruction of VOCs. The burner system is designed to provide stable and controlled combustion conditions within the RTO.
• 5. Heat Recovery System: The heat recovery system enables energy efficiency in an RTO. It captures and preheats the incoming process air by utilizing the heat energy from the outgoing exhaust stream. The heat exchange occurs between the ceramic media beds, allowing for significant energy savings and reducing the overall operating costs of the RTO.
• 6. Control System: The control system of an RTO monitors and regulates the operation of various components. It ensures proper valve sequencing, temperature control, and safety interlocks. The control system optimizes the performance of the RTO, maintains the desired destruction efficiency, and provides necessary alarms and diagnostics for efficient operation and maintenance.
• 7. Stack or Exhaust System: The stack or exhaust system is responsible for releasing the treated and cleaned gases into the atmosphere. It may include a stack, ductwork, and any necessary emission monitoring equipment to ensure compliance with environmental regulations.

These key components work together in a coordinated manner to provide efficient air pollution control in a regenerative thermal oxidizer. Each component plays a critical role in achieving high VOC destruction efficiency, energy recovery, and compliance with environmental standards.

editor by Dream 2024-04-30