China manufacturer Rto Rotary Type Regenerative Thermal Oxidizer

基本訊息

型號

Amazing RTO

類型

Incinerator

High Efficiency

100

Energy Saving

100

Low Maintenance

100

Easy Operation

100

商標

Bjamazing

運輸套餐

Overseas

Specification

111

起源

China

HS Code

2221111

產品描述

RTO

蓄熱式熱氧化器

Compared with traditional catalytic combustion,; direct thermal oxidizer,; RTO has the merits of high heating efficiency,; low operation cost,; and the ability to treat large flux low concentration waste gas.; When VOCs concentration is high,; secondary heat recycle can be realized,; which will greatly reduce the operation cost.; Because RTO can preheat the waste gas by levels through ceramic heat accumulator,; which could make the waste gas to be completely heated and cracked with no dead corner(treatment efficiency>99%);,;which reduce the NOX in the Exhausting gas,; if the VOC density >1500mg/Nm3,; when the waste gas reach cracking area,; it has been heated up to cracking temperature by heat accumulator,; the burner will be closed under this condition.;

RTO can be devided into chamber type and rotary type according to difference operation mode.; Rotary type RTO has advantages in system pressure,; temperature stability,; investment amount,; etc

Regenerative Thermal Oxidizer,; Regenerative Thermal Oxidizer,; Regenerative Thermal Oxidizer,;  Thermal Oxidizer,; Thermal Oxidizer,; Thermal Oxidizer,; oxidizer,; oxidizer,; oxidizer,; incinerator,; incinerator,; incinerator,; waste gas treatment,; waste gas treatment,; waste gas treatment,; VOC treatment,; VOC treatment,; VOC treatment,; RTO,; RTO,; RTO,; Rotary RTO,; Rotary RTO,; Rotary RTO,; Chamber RTO,; Chamber RTO,; Chamber RTO

Address: 8 floor, E1, Pinwei building, Dishengxi road, Yizhuang, ZheJiang , China

業務類型: 製造商/工廠, 貿易公司

Business Range: Electrical & Electronics, Industrial Equipment & Components, Manufacturing & Processing Machinery, Metallurgy, Mineral & Energy

Management System Certification: ISO 9001, ISO 14001

Main Products: Rto, Color Coating Line, Galvanizing Line, Air Knife, Spares for Processing Line, Coater, Independent Equipments, Sink Roll, Revamping Project, Blower

Company Introduction: ZheJiang Amazing Science & Technology Co., Ltd is a thriving Hi-tech company, located in ZheJiang Economic and Technological Development Area(BDA). Adhering to the concept of Realistic, Innovative, Focused and Efficient, our company mainly serve the waste gas treatment (VOCs) Industry and metallurgical equipment of China and even whole world. We have advanced technology and rich experience in VOCs waste gas treatment project, the reference of which has been successfully applied to the industry of coating, rubber, electronic, printing, etc. We also have years of technology accumulation in the research and manufacturing of flat steel processing line, and possess nearly 100 of application example.

Our company focus on the research, design, manufacturing, installation and commissioning of VOCs organic waste gas treatment system and the revamping and updating project for energy saving and environmental protection of flat steel processing line. We can provide customers the complete solutions for environmental protection, energy saving, product quality improvement and other aspects.

We are also engaged in various spares and independent equipment for color coating line, galvanizing line, pickling line, like roller, coupler, heat exchanger, recuperator, air knife, blower, welder, tension leveler, skin pass, expansion joint, shear, jointer, stitcher, burner, radiant tube, gear motor, reducer, etc.

Are regenerative thermal oxidizers noisy during operation?

Regenerative thermal oxidizers (RTOs) can generate noise during operation, but the noise levels are typically within acceptable limits and can be managed effectively. The noise produced by an RTO depends on various factors, including the specific design of the system, the size and type of fans or blowers used, and the velocity and pressure of the exhaust gases.

Here are some considerations regarding the noise produced by RTOs:

• Noise Control Measures: RTO manufacturers often incorporate noise control measures into the design of the system. These measures may include the use of silencers or sound-absorbing materials at strategic locations within the RTO to minimize noise propagation. By implementing these measures, the noise generated by the RTO can be reduced to acceptable levels.
• Location and Distance: The location of the RTO within the facility can impact the perceived noise levels. Placing the RTO in an area away from sensitive receptors, such as occupied spaces or noise-sensitive equipment, can help minimize the impact of noise on the facility’s occupants or neighboring properties.
• Enclosures and Insulation: Additional noise reduction can be achieved by enclosing the RTO in a soundproof housing or using insulation materials to dampen the noise. These enclosures or insulation can help contain and absorb the noise generated by the RTO, reducing its impact on the surrounding environment.
• Operational Considerations: Proper maintenance and regular inspections of the RTO are essential to ensure optimal performance and minimize noise generation. Malfunctioning components, worn-out bearings, or imbalanced fans can contribute to increased noise levels. By conducting routine maintenance and addressing any issues promptly, the noise levels can be kept under control.
• Regulatory Compliance: Noise regulations and guidelines may vary depending on the jurisdiction and the specific industrial sector. It is important to assess and comply with applicable noise regulations to ensure that the RTO’s operation meets the required noise limits.

Overall, while RTOs can produce noise during operation, appropriate design considerations, noise control measures, and compliance with applicable regulations can help mitigate the impact of the noise. Consulting with RTO manufacturers, acoustical engineers, or environmental consultants can provide valuable insights and recommendations for managing noise associated with RTO operation.

蓄熱式熱氧化器如何處理系統中顆粒物的堆積？

蓄熱式熱氧化器 (RTO) 採用各種機制來處理系統中顆粒物的堆積。灰塵、煙灰或其他固體顆粒等顆粒物會隨著時間的推移而積累，並可能影響 RTO 的性能和效率。以下是 RTO 處理顆粒物堆積的一些方法：

• 預過濾： RTO 可以採用預過濾系統，例如旋風分離器或袋式過濾器，以在較大的顆粒物質進入氧化器之前將其去除。這些預過濾器捕獲並收集顆粒，防止它們進入 RTO 並減少積聚的可能性。
• 自潔效果： RTO 的設計目的是對熱交換介質具有自清潔作用。在 RTO 運作期間，熱廢氣流過介質會導致顆粒燃燒或分解，從而最大限度地減少顆粒的累積。高溫和湍流有助於保持介質表面清潔，並降低大量顆粒堆積的風險。
• 吹掃週期： RTO 通常將吹掃循環作為其操作的一部分。這些循環涉及將少量清潔空氣或氣體引入系統以清除任何殘留的顆粒物質。吹掃空氣有助於去除或燒掉任何黏附在介質上的顆粒，確保介質的持續清潔。
• 定期維護： 定期維護對於防止 RTO 中顆粒物堆積過多至關重要。維護活動可能包括檢查和清潔熱交換介質，檢查和更換任何磨損的墊圈或密封件，以及監控系統是否有任何顆粒積聚的跡象。定期維護有助於確保最佳性能，並最大限度地降低與顆粒物堆積相關的操作問題的風險。
• 監控與警報： RTO 配備了監控系統，可追蹤壓力差、溫度和流量等各種參數。這些系統可以檢測任何可能表明顆粒物堆積的異常情況或過度壓力降。可以觸發警報和警報來通知操作員，提示他們採取適當的行動，例如啟動維護或清潔程序。

值得注意的是，用於處理顆粒物堆積的具體策略可能會根據 RTO 的設計和配置以及所處理的顆粒物的特性而有所不同。 RTO製造商和營運商應考慮這些因素並採取適當的措施，以確保系統中顆粒物的有效管理。

透過結合預過濾、利用自清潔效應、實施吹掃循環、進行定期維護以及採用監控系統，RTO 可以有效處理和減少顆粒物積聚，從而長期保持其性能和效率。

What are the key components of a regenerative thermal oxidizer?

A regenerative thermal oxidizer (RTO) typically consists of several key components that work together to achieve effective air pollution control. The main components of an RTO include:

• 1. Combustion Chamber: The combustion chamber is where the oxidation of the pollutants takes place. It is designed to withstand high temperatures and house the ceramic media beds that facilitate heat exchange and VOC destruction. The combustion chamber provides a controlled environment for the combustion process to occur efficiently.
• 2. Ceramic Media Beds: Ceramic media beds are the heart of an RTO. They are filled with structured ceramic materials that act as a heat sink. The media beds alternate between the inlet and outlet sides of the RTO, allowing for efficient heat transfer. As the VOC-laden air passes through the media beds, it is heated by the stored heat from the previous cycle, promoting combustion and VOC destruction.
• 3. Valves or Dampers: Valves or dampers are used to direct the airflow within the RTO. They control the flow of the process air and the direction of the exhaust gases during the different phases of operation, such as the heating, combustion, and cooling cycles. Proper valve sequencing ensures optimal heat recovery and VOC destruction efficiency.
• 4. Burner System: The burner system provides the necessary heat to raise the temperature of the incoming process air to the required combustion temperature. It typically uses natural gas or another fuel source to generate the heat energy needed for the destruction of VOCs. The burner system is designed to provide stable and controlled combustion conditions within the RTO.
• 5. Heat Recovery System: The heat recovery system enables energy efficiency in an RTO. It captures and preheats the incoming process air by utilizing the heat energy from the outgoing exhaust stream. The heat exchange occurs between the ceramic media beds, allowing for significant energy savings and reducing the overall operating costs of the RTO.
• 6. Control System: The control system of an RTO monitors and regulates the operation of various components. It ensures proper valve sequencing, temperature control, and safety interlocks. The control system optimizes the performance of the RTO, maintains the desired destruction efficiency, and provides necessary alarms and diagnostics for efficient operation and maintenance.
• 7. Stack or Exhaust System: The stack or exhaust system is responsible for releasing the treated and cleaned gases into the atmosphere. It may include a stack, ductwork, and any necessary emission monitoring equipment to ensure compliance with environmental regulations.

These key components work together in a coordinated manner to provide efficient air pollution control in a regenerative thermal oxidizer. Each component plays a critical role in achieving high VOC destruction efficiency, energy recovery, and compliance with environmental standards.

editor by CX 2024-02-27