China Good quality Rto Regenerative Thermal Oxidizer

基本訊息

型號

Amazing RTO

類型

Incinerator

High Efficiency

100

Energy Saving

100

Low Maintenance

100

Easy Operation

100

商標

Bjamazing

運輸套餐

Overseas

Specification

111

起源

China

HS Code

2221111

產品描述

RTO

蓄熱式熱氧化器

Compared with traditional catalytic combustion,; direct thermal oxidizer,; RTO has the merits of high heating efficiency,; low operation cost,; and the ability to treat large flux low concentration waste gas.; When VOCs concentration is high,; secondary heat recycle can be realized,; which will greatly reduce the operation cost.; Because RTO can preheat the waste gas by levels through ceramic heat accumulator,; which could make the waste gas to be completely heated and cracked with no dead corner(treatment efficiency>99%);,;which reduce the NOX in the Exhausting gas,; if the VOC density >1500mg/Nm3,; when the waste gas reach cracking area,; it has been heated up to cracking temperature by heat accumulator,; the burner will be closed under this condition.;

RTO can be devided into chamber type and rotary type according to difference operation mode.; Rotary type RTO has advantages in system pressure,; temperature stability,; investment amount,; etc

Regenerative Thermal Oxidizer,; Regenerative Thermal Oxidizer,; Regenerative Thermal Oxidizer,;  Thermal Oxidizer,; Thermal Oxidizer,; Thermal Oxidizer,; oxidizer,; oxidizer,; oxidizer,; incinerator,; incinerator,; incinerator,; waste gas treatment,; waste gas treatment,; waste gas treatment,; VOC treatment,; VOC treatment,; VOC treatment,; RTO,; RTO,; RTO,; Rotary RTO,; Rotary RTO,; Rotary RTO,; Chamber RTO,; Chamber RTO,; Chamber RTO

Address: 8 floor, E1, Pinwei building, Dishengxi road, Yizhuang, ZheJiang , China

業務類型: 製造商/工廠, 貿易公司

Business Range: Electrical & Electronics, Industrial Equipment & Components, Manufacturing & Processing Machinery, Metallurgy, Mineral & Energy

Management System Certification: ISO 9001, ISO 14001

Main Products: Rto, Color Coating Line, Galvanizing Line, Air Knife, Spares for Processing Line, Coater, Independent Equipments, Sink Roll, Revamping Project, Blower

Company Introduction: ZheJiang Amazing Science & Technology Co., Ltd is a thriving Hi-tech company, located in ZheJiang Economic and Technological Development Area(BDA). Adhering to the concept of Realistic, Innovative, Focused and Efficient, our company mainly serve the waste gas treatment (VOCs) Industry and metallurgical equipment of China and even whole world. We have advanced technology and rich experience in VOCs waste gas treatment project, the reference of which has been successfully applied to the industry of coating, rubber, electronic, printing, etc. We also have years of technology accumulation in the research and manufacturing of flat steel processing line, and possess nearly 100 of application example.

Our company focus on the research, design, manufacturing, installation and commissioning of VOCs organic waste gas treatment system and the revamping and updating project for energy saving and environmental protection of flat steel processing line. We can provide customers the complete solutions for environmental protection, energy saving, product quality improvement and other aspects.

We are also engaged in various spares and independent equipment for color coating line, galvanizing line, pickling line, like roller, coupler, heat exchanger, recuperator, air knife, blower, welder, tension leveler, skin pass, expansion joint, shear, jointer, stitcher, burner, radiant tube, gear motor, reducer, etc.

Are regenerative thermal oxidizers noisy during operation?

Regenerative thermal oxidizers (RTOs) can generate noise during operation, but the noise levels are typically within acceptable limits and can be managed effectively. The noise produced by an RTO depends on various factors, including the specific design of the system, the size and type of fans or blowers used, and the velocity and pressure of the exhaust gases.

Here are some considerations regarding the noise produced by RTOs:

• Noise Control Measures: RTO manufacturers often incorporate noise control measures into the design of the system. These measures may include the use of silencers or sound-absorbing materials at strategic locations within the RTO to minimize noise propagation. By implementing these measures, the noise generated by the RTO can be reduced to acceptable levels.
• Location and Distance: The location of the RTO within the facility can impact the perceived noise levels. Placing the RTO in an area away from sensitive receptors, such as occupied spaces or noise-sensitive equipment, can help minimize the impact of noise on the facility’s occupants or neighboring properties.
• Enclosures and Insulation: Additional noise reduction can be achieved by enclosing the RTO in a soundproof housing or using insulation materials to dampen the noise. These enclosures or insulation can help contain and absorb the noise generated by the RTO, reducing its impact on the surrounding environment.
• Operational Considerations: Proper maintenance and regular inspections of the RTO are essential to ensure optimal performance and minimize noise generation. Malfunctioning components, worn-out bearings, or imbalanced fans can contribute to increased noise levels. By conducting routine maintenance and addressing any issues promptly, the noise levels can be kept under control.
• Regulatory Compliance: Noise regulations and guidelines may vary depending on the jurisdiction and the specific industrial sector. It is important to assess and comply with applicable noise regulations to ensure that the RTO’s operation meets the required noise limits.

Overall, while RTOs can produce noise during operation, appropriate design considerations, noise control measures, and compliance with applicable regulations can help mitigate the impact of the noise. Consulting with RTO manufacturers, acoustical engineers, or environmental consultants can provide valuable insights and recommendations for managing noise associated with RTO operation.

Can regenerative thermal oxidizers handle corrosive exhaust gases?

Regenerative thermal oxidizers (RTOs) can be designed to handle corrosive exhaust gases effectively. However, the ability of an RTO to handle corrosive gases depends on several factors, including the choice of construction materials, operating conditions, and the specific corrosive nature of the exhaust gases. Here are some key points regarding the handling of corrosive exhaust gases in RTOs:

• Material Selection: The selection of appropriate construction materials is crucial when dealing with corrosive gases. RTOs can be constructed using materials that offer high resistance to corrosion, such as stainless steel, corrosion-resistant alloys (e.g., Hastelloy, Inconel), or coated materials. The choice of materials depends on the specific corrosive compounds present in the exhaust gases and their concentrations.
• Corrosion-Resistant Coatings: In addition to selecting corrosion-resistant materials, applying protective coatings can enhance the resistance of the RTO components to corrosive gases. Coatings such as ceramic coatings, epoxy coatings, or acid-resistant paints can provide an extra layer of protection against corrosion.
• Temperature Control: Maintaining appropriate operating temperatures in the RTO can help mitigate the corrosive effects of the exhaust gases. Higher temperatures can promote the decomposition of corrosive compounds, reducing their corrosive potential. Additionally, operating at higher temperatures can enhance the self-cleaning effect and prevent the accumulation of corrosive deposits on the surfaces.
• Gas Conditioning: Prior to entering the RTO, the exhaust gases can undergo gas conditioning processes to reduce their corrosive nature. This may involve pre-treatment methods such as scrubbing or neutralization to remove or neutralize corrosive compounds and reduce their concentration.
• Monitoring and Maintenance: Regular monitoring of the RTO performance and periodic maintenance are essential to ensure the effective handling of corrosive exhaust gases. Monitoring systems can track variables such as temperature, pressure, and gas composition to detect any deviations that may indicate corrosion-related issues. Proper maintenance, including cleaning and inspection of the components, helps identify and address any corrosion concerns in a timely manner.

It is important to note that the corrosiveness of exhaust gases can vary significantly depending on the specific industrial process and the pollutants involved. Therefore, when designing an RTO for handling corrosive gases, it is advisable to consult with experienced engineers or RTO manufacturers who can provide guidance on the appropriate design considerations and material selection.

By employing suitable materials, coatings, temperature control, gas conditioning, and maintenance practices, RTOs can effectively handle corrosive exhaust gases while ensuring their long-term performance and durability.

哪些行業常用蓄熱式熱氧化器？

蓄熱式熱氧化器 (RTO) 廣泛應用於產生揮發性有機化合物 (VOC)、有害空氣污染物 (HAP) 和其他有害排放物的各個產業。通常使用 RTO 進行空氣污染控制的一些行業包括：

• 化學品製造：RTO 廣泛應用於生產溶劑、油漆、塗料、黏合劑和其他化學產品的化學製造過程。這些行業經常產生大量的揮發性有機化合物，需要有效的控制和減排。
• 印刷和包裝：印刷和包裝行業利用 RTO 來控製油墨乾燥、塗佈和溶劑型製程中的 VOC 和 HAP 排放。 RTO 確保遵守環境法規，同時保持高品質的列印標準。
• 藥品：藥品製造過程通常涉及溶劑和有機化合物的使用，導致揮發性有機化合物的產生。 RTO 為捕捉和銷毀這些排放物提供了有效的解決方案，確保安全、環保的生產環境。
• 油漆和塗料：RTO 通常用於油漆和塗料生產設施，以控制固化和乾燥過程中的 VOC 排放。透過有效破壞 VOC，RTO 有助於減少這些產業對環境的影響，同時維持產品品質。
• 家具和木工：家具和木工行業利用 RTO 來控制噴漆、染色和清漆等工藝的排放。 RTO 有助於去除這些操作過程中產生的 VOC 和 HAP，促進更健康的工作環境並減少對周圍社區的影響。
• 食品加工：某些食品加工作業會產生揮發性有機化合物和有氣味的化合物。 RTO 在這些行業中用於捕獲和處理烹飪、烘焙、油炸和其他食品相關過程中的排放。 RTO 確保符合空氣品質標準，同時最大限度地減少對食品品質和安全的影響。
• 化學品儲存和處理：涉及化學品儲存和處理的設施，例如散裝液體終端和化學品配送中心，可以利用 RTO 來控制排放和蒸氣回收系統的排放。 RTO 有助於減少各種儲存和轉移作業過程中 VOC 和 HAP 的釋放。

這些只是幾個例子，RTO 可以在許多其他產生 VOC 和 HAP 的行業中找到。 RTO 為空氣污染控制提供了多功能且有效的解決方案，確保遵守環境法規並促進永續的工業實踐。

editor by CX 2024-02-19